Laboratory Water


ULTRA PURE WATER TREATMENT SYSTEMS FOR LABORATORY EQUIPMENT

With reverse osmosis systems, storage tank, and deionizer packages that produce up to 18 meg ohm water quality, AmeriWater has the right system to supply your hospital with ultra pure lab water. Systems meet CSLI/CAA/ASTM Type I through Type IV water quality requirements.

Build a Complete Water Treatment System

Select a Reverse Osmosis
AmeriWater’s unique cabinet design provides superior durability. With the Reverse Osmosis for Laboratory Waterpump, membranes and pretreatment located inside, the system is so quiet you won’t even know it is running. When it’s time for maintenance, the hinged doors on the front and rear of the cabinet allow quick and easy access. Note: The anti-scalant and carbon pretreatment for the HCR03 and HCR04 are located on the outside of the cabinet for easy access.

  • Pre-carbon block filter
  • Anti-scalant feed to prevent hard water scale on reverse osmosis
  • Controller with conductivity of feed and product water
  • Disinfection is quick and easy. With a simple push of the keypad, the RO can be disinfected with PAA in only one hour.
  • Microprocessor controller keeps you informed of operating conditions with backlit LCD displaying product and feed water conductivity, product water temperature, operating hours, percent rejection, and a variety of operating status messages. Programmable flush keeps RO fresh between uses.
Model 00HC-0015 00HC-0045 00HC-0060 00HC-0075
Product Flow GPD* 800 2,200 4,200 5,600
Number of Membranes 2 2 3 4
Power Volt/Amp 120/13 120/14 230/7 230/8
Feed Flow GPM 3 5 7 8
Percent Rejection > 96
* Rated nominal flow at 77F, 1500 ppm of NaCl at pump psi of 170 and pH 7.5.

 

Select a Laboratory Storage Tank
The laboratory storage tank, with UV disinfector and submicron filter, is Laboratory Storage Tankintended for use with a reverse osmosis unit and a deionizer providing Type II water. This system is used on washer/disinfectors, lab, glassware washers, and blood analyzers. A 55 or 100 gallon storage tank with demand pump package provides up to 4 GPM for a ½” recirculating loop.

  • 55 or 100 gallon storage tank with sealed lid and pump package
  • UV sterilizer
  • Includes a resistivity monitor with alarm
  • Post submicron filtration 0.2um
  • An end of loop relief valve
  • Low resistivity alarm
  • Storage tank empty pump shutdown

 

Dual Worker/Polisher Deionizer
The Silex dual worker/polisher deionizer is designed for use with the Dual Worker/Polisher Deionizerlaboratory system to polish the water from the RO storage tank. Uses include labs, critical spot free rinsing, chemical dilution and mixing, humidification, etc. The Silex deionizer uses packs of mixed bed resin that are sent back to the regeneration center to be recharged. A spare set is provided so they can be alternated for regeneration. The regeneration service is only a fraction of the cost of disposable deionizer beds or cartridges. The all PVC housings are durable and the packs are easy to exchange.

 

LEARN MORE:

RO SPECIFICATIONS:

  • Pressure Min/Max PSI: 20/90
  • Temperature: 41-100°F
  • Feed SDI: < 5
  • Chlorine Max to Membranes: 0.1 PPM
  • ETL Listed, Conforms to UL Std 61010-1
  • Certified CAN/CSA C22.2 No. 61010-1

TANK SPECIFICATIONS:

  • Drain: One 1½” Floor Drain or Sink
  • Feed Water Quality: Low Conductivity
  • Distribution Pump Output: 4 GPM at 55 PSIG
  • Electrical: 115V, 20 Amps GFI Dedicated Circuit, 3 Prong Receptacle
  • ETL Listed, Conforms to UL Std 61010-1
  • Certified CAN/CSA C22.2 No. 61010-1
  • Seismic OPA-2202-7

 

DEIONIZER SPECIFICATIONS:

  • Inlet/Outlet: ½” NPT
  • Capacity: ½ Cubic Foot for Each Housing
  • Flow Rate: Up to 4 GPM
  • Maximum Feed Pressure: 50 PSI Without Regulator Kit
  • Maximum Temperature: 110°F
  • Bottom Drain and Sample Port: ⅜” Ball Valve